Master TS-2K Line Marking

Item number:

Line Marking for sporthalls and gyms

  • Very strong and resistant
  • Indoor climate labelled
  • Anti-slip certified - DIN 51130:R9

*The wood sample is shown on beech

2.25 L

Product details

  • Description
  • Specifications
  • Technical data sheet
  • Safety data sheet

VOC:

Max110 g/l, maximum VOC content (A/i (WB)): 140 g/l.

Density:

1.00-1.10 g/ml.

pH-value:

pH 7-8

Shelf life:

1 year

Application Temperature:

+15-25°C and approx. 50% air humidity.

Coverage:

6-10 m²/L

Colours:

Yellow, Blue, Green, White, Black, Red

Cleaning of tools:

Use water

Storage:

+10-25°C. Keep out of reach of children. Do not expose to heat (e.g. sunlight). Store frost-free during winter and cool during summer.

Packaging:

2.25 L

Viscosity:

20-25 Sec. DIN Cup 4

Pot life:

The mixture must be used within 5 hours. Shake/stir thoroughly before use.

Mixing ratio:

10% or 500 ml to 5 L lacquer

Drying time:

3-4 hours at 20°C

Recommendation:

If Line Marking is not applied within 24 hours the surface must be re-sanded.

Fully hard:

5 days at 20°C

Master TS-2K Lacquer is a two-component water-based floor lacquer approved for sports areas and multi-purpose halls according to the European DS/EN 14904. It offers a strong protection, excellent durability and an incredibly high resistance to heel marks, abrasion and scratches. Master TS-2K Lacquer is also indoor climate labelled, DIBt-approved and is approved according to DIN 51130: R9. Master TS-2K Lacquer is used in combination with WOCA Line Marking which is available in 6 different colours.

Worksteps

Instructions
Products in use
It is important that both wood and lacquer have a temperature of min. 15°C, but preferably around 20°C, and a humidity of approx. 50 %. The relative humidity must not vary more than 30 % during the year. Provide good ventilation in the room for drying time and evaporation. Master TS-2K Lacquer adheres to most surfaces with the right preparation and drying time. Always remember to do a test run at a less visible place to check the compatibility of the wood and Master TS-2K Lacquer. Scratch with a coin to check the adhesion. Alternatively, try WOCA Master Multi Primer for exotic wood species or old wood previously treated with oil or wax.

  1. Application day 1: Sand with sandpaper GRIT 100-120. Vacuum thoroughly and wipe the floor with a cloth/mop heavily wrung in clean water. Let the floor dry for 1-2 hours before applying the WOCA Master Base Primer. Apply the Master Base Primer wet-on-wet and leave it to dry 3-4 hours at 20°C, depending on humidity.
  2. Mix WOCA Master Classic 2K Hardener and Master TS-2K Lacquer and shake thoroughly. Leave the mixture to stand for teen minutes to allow the hardener to activate and shake thoroughly again. Apply 1-2 coat of Master TS-2K Lacquer. Apply the Lacquer wet-on-wet to avoid overlap. Let the surface dry for 3-4 hours. Ensure good ventilation until the next day.
  3. Application day 2: De-nip the surface with GRIT 120-180 and vacuum thoroughly afterwards. Cover with tape along all desired lines and areas. Apply a tape with low adhesive strength. It is important that the tape adheres close to the floor to ensure straight edges. WOCA recommends TESA 4334. For best results, we recommend sealing the tape edges with Master TS-2K Lacquer. Leave it to dry for 1-2 hours (touch dry).
  4. Mix Master TS-2K Line Marking and Master Classic 2K Hardener and shake thoroughly. Leave the mixture to stand for ten minutes to allow the hardener to activate and shake thoroughly again. To avoid color differences, different batch no. must be mixed before application. Apply Master TS-2K Line Marking with a small lacquer roller 9 mm, foam roller or brush and allow to dry. Remove the tape after 2-6 hours after applying Line Marking and let the surface dry for an additional 12 hours as a minimum or until the next day. Ensure good ventilation.
  5. Application day 3: Mix Master TS-2K Line Marking and Master Classic 2K Hardener and shake thoroughly. Leave the mixture to stand for ten minutes to allow the hardener to activate and shake thoroughly again. Apply a coat of Master TS-2K Line Marking. The finished lacquered floor can be used carefully after approx. 6-7 hours with good ventilation and is fully hardened after 5 days at 20°C.
Master TS 2K Line Marking white and yellow may need 2 coats to achieve a full color