Master XP-2K Lacquer

Item number:

Extreme performance for public areas

  • Extreme strength and resistance
  • R9 (R10 Cerftified by adding WOCA Anti-Slip Additive)
  • Full and rich appearance
  • Indoor climate labelled
  • Fire classification according to DIN EN 13501: Bfl-s1
5 L

Product details

  • Description
  • Specifications
  • Technical data sheet
  • Safety data sheet

Density:

1.00-1.10 g/ml.

pH-value:

pH 7-8

Shelf life:

2 years

Application Temperature:

+15-25°C and approx. 50% air humidity.

Coverage:

8-10 m²/L

Colours:

Colourless - Matt, Colourless - Silk-matt, Colourless - Silk-gloss

Cleaning of tools:

Use water

Storage:

+10-25°C. Keep out of reach of children. Do not expose to heat (e.g. sunlight). Store frost-free during winter and cool during summer.

Packaging:

5 liters

Non-slip (DIN 51130):

R10

Viscosity:

20-25 Sec. DIN Cup 4

Pot life:

The mixture must be used within 5 hours. Shake/stir thoroughly before use.

Odour:

Characteristic

Solid content:

Approx. 32%

Mixing ratio:

10% or 500 ml to 5 L lacquer

Between coats:

2-3 hours at 20°C

Light use:

4-6 hours at 20°C

Recommendation:

Wait 24 hours before putting furniture on the floor. Wait 5 days before covering with carpets and washing. If drying times are not followed, this can result in poor adhesion and reduced resistance. For each coat of lacquer, drying times will be increased. High temperature and low air humidity will reduce drying times. Low temperature and high air humidity will extend drying times. During summer time or in high temperatures, use retarder and filter '180-220 my'.

Fully hard:

5 days at 20°C

Master XP-2K Lacquer is a water-based, two-component floor lacquer remarkable for its extremely high resistance to black heel marks, scratches and stains. Its superior performance is perfectly suited for high traffic public areas, such as canteens and stairs, as its extreme protection and resistance make the floors easy to clean and maintain. The wood is left with a rich and full appearance, due to the high solids content.

Worksteps

Instructions
Products in use
It is important that both wood and lacquer have a temperature of min. 15°C (preferably around 20°C) and air humidity of approx. 50%. Make sure that the room is well-ventilated for optimal evaporation and drying time. For the final sanding to bare wood, use grit 100-120 sandpaper or sanding pad. Vacuum thoroughly and wipe the floor down afterwards, using a tightly-wrung water-soaked mop/cloth. Please note: WOCA Intensive Wood Cleaner can help to remove contaminates from fully sanded wooden floors before priming or lacquering. Please allow floor to fully dry overnight. The floor must be completely dry before priming. When priming, use WOCA Master Base Primer for newly sanded wood to reduce side bonding. Alternatively, try WOCA Master Multi Primer for exotic wood species or old wood previously treated with oil or wax.

Always remember to test on a less visible spot to check the compatibility of the surface with the product.

  1. Apply the primer. When dry, mix Master Classic 2K Hardener with the lacquer and shake thoroughly before use. Leave the mixture to stand for ten minutes before use, to allow the hardener to activate.
  2. A coat of Master XP-2K Lacquer Lacquer should be applied undiluted, using a brush or roller. Leave the surface to dry until next day.
  3. Sand the surface with 120-200 and vacuum clean the surface thoroughly.
  4. Apply the final coat of Master XP-2K Lacquer with hardener (freshly mixed).
Water and coloured fluids, such as red wine and coffee, must be wiped off immediately to prevent staining.