Master TS-2K Line Marking

Item number:

Line Marking for sporthalls and gyms

  • Very strong and resistant
  • Approved for sports - DIN EN 14904
  • Indoor climate labelled
  • Anti-slip certified - DIN 51130:R9

A+

All floor coating (care/treatment) products marketed in France are obliged to certify their products with an A+. The aim is to improve indoor air quality and, at the same time, enable consumers to choose environmentaly friendly products.

DiBt

DIBt is a German institute that tests and issues technical approvals for building materials.The aim is to improve the working climate for floor installers whilst ensuring a safe indoor air quality for the final consumer.

Danish Indoor Climate Labelling

Danish Interior Climate Labelling is a voluntary labelling system for products and materials which can document the effect of degassing. Indoor climate labelled materials are a natural component in sustainable construction, where a good indoor air quality contributes to social sustainability.

Anti Slip - R9

DIN 51130 is a standardised anti-slip test for flooring. It is typically used for work places and official buildings where there is a requirement that products have the anti-slip test DIN 51130 with a classification from R9 to R13.

Sports test

This European standard specifies requirements for surfaces for indoor sports facilities.

Fire test

The European Standard EN 13501-1, which measures the reactions of building materials to fire. The reaction is determined by how much a product contributes to a fire and is classified from A to F.

EN 71-3

A European standard test for contamination of harmful substances. This test is especially relevant for worktops, toys and kitchen utensils.

Food contactable

If you wish to avoid a spillover of harmful substances from worksurfaces to food then look for the Glass and fork symbol. The manufacturer has to document that the surface treatment of the product does not release release harmful substances into food products. This is tested by an independent third party who assesses the composition of the product. Look for the symbol!

IBR

Voluntary labelling that ensures the best possible indoor climate as well as minimum of bad odours and other forms of contamination. The product is tested by a third party independent examiner.

Nordic Swan

Nordic Swan is the official ecolabel in Scandinavia. The Nordic Swan label creates sustainable solutions based on life-cycle assessment and an overall desire to reduce the environmental impact from production and consumption of goods. This makes it easy for consumer and professional shoppers to choose the best products and services for the environment.

Anti Slip - R10

DIN 51130 is a standardised anti-slip test for flooring. It is typically used for work places and official buildings where there is a requirement that products have the anti-slip test DIN 51130 with a classification from R9 to R13.

Anti Slip - R11

DIN 51130 is a standardised anti-slip test for flooring. It is typically used for work places and official buildings where there is a requirement that products have the anti-slip test DIN 51130 with a classification from R9 to R13.

Emicode EC1 Plus

*The wood sample is shown on beech
2.25 L
Find retailer

Product details

  • Description
  • Specifications
  • Technical data sheet
  • Safety data sheet

Density:

1.00-1.10 g/ml.

pH-value:

pH 7-8

Shelf life:

1 year

Application Temperature:

+15-25°C and approx. 50% air humidity.

Coverage:

6-10 m²/L

Colours:

Yellow, Blue, Green, White, Black, Red

Cleaning of tools:

Use water

Storage:

+10-25°C. Keep out of reach of children. Do not expose to heat (e.g. sunlight). Store frost-free during winter and cool during summer.

Packaging:

2.25 liters

Viscosity:

20-25 Sec. DIN Cup 4

Pot life:

The mixture must be used within 5 hours. Shake/stir thoroughly before use.

Solid content:

Approx. 32%

Mixing ratio:

10% or 500 ml to 5 L lacquer

Drying time:

3-4 hours at 20°C

Recommendation:

If Line Marking is not applied within 24 hours the surface must be re-sanded.

Fully hard:

5 days at 20°C

Master TS-2K Lacquer is a two-component water-based floor lacquer approved for sports areas and multi-purpose halls according to the European DS/EN 14904. It offers a strong protection, excellent durability and an incredibly high resistance to heel marks, abrasion and scratches. Master TS-2K Lacquer is also indoor climate labelled, DIBt-approved, approved according to DIN 51130: R9 and fire tested according to EN 12501-1: 2018: Bfl1-S1.Master TS-2K Lacquer is used in combination with WOCA Line Marking which is available in 6 different colours:RAL 1021 YellowRAL 3000 RedRAL 5010 BlueRAL 6029 GreenRAL 9016 White RAL 9017 Black

Worksteps

Instructions
Products in use
It is important that both wood and lacquer have a temperature of min. 15°C, but preferably around 20°C, and a humidity of approx. 50 %. The relative humidity must not vary more than 30 % during the year. Provide good ventilation in the room for drying time and evaporation. Master TS-2K Lacquer adheres to most surfaces with the right preparation and drying time. Always remember to do a test run at a less visible place to check the compatibility of the wood and Master TS-2K Lacquer. Scratch with a coin to check the adhesion. Alternatively, try WOCA Master Multi Primer for exotic wood species or old wood previously treated with oil or wax.

  1. Application day 1: Sand with sandpaper or GRIT 100-120. Vacuum thoroughly and wipe the floor with a cloth/mop heavily wrung in clean water. Let the floor dry for 3-4 hours at 20°C before applying the WOCA Master Base Primer. Apply the Master Base Primer wet-on-wet and leave it to dry 3-4 hours at 20°C, depending on humidity.
  2. Mix WOCA Master Classic 2K Hardener and Master TS-2K Lacquer and shake thoroughly. Leave the mixture to stand for teen minutes to allow the hardener to activate and shake thoroughly again. Apply 1-2 coat of Master TS-2K Lacquer. Apply the Lacquer wet-on-wet to avoid overlap. Let the surface dry for 3-4 hours. Ensure good ventilation until the next day.
  3. Application day 2: De-nip the surface with GRIT 120-180 and vacuum thoroughly afterwards. Cover with tape along all desired lines and areas. Apply a tape with low adhesive strength. It is important that the tape adheres close to the floor to ensure straight edges. WOCA recommends TESA 4334. For best results, we recommend sealing the tape edges with Master TS-2K Lacquer. Leave it to dry for 1-2 hours (touch dry).
  4. Mix Master TS-2K Line Marking and Master Classic 2K Hardener and shake thoroughly. Leave the mixture to stand for ten minutes to allow the hardener to activate and shake thoroughly again. To avoid color differences, different batch no. must be mixed before application. Master TS-2K Line Marking with a small lacquer roller 9 mm, foam roller or brush and allow to dry may need two coats to achieve a full color).Remove the tape after 2-6 hours after applying Line Marking and let the surface dry for an additional 12 hours as a minimum or until the next day. Ensure good ventilation.
  5. Application day 3: Mix Master TS-2K Line Marking and Master Classic 2K Hardener and shake thoroughly. Leave the mixture to stand for ten minutes to allow the hardener to activate and shake thoroughly again. Apply a coat of Master TS-2K Line Marking. The finished lacquered floor can be used carefully after approx. 3-4 hours at 20°C with good ventilation and is fully hardened after 5 days at 20°C.
Master TS 2K Line Marking white and yellow may need 2 coats to achieve a full color

Products you need

  • Master Base Primer
    Master Base Primer

    Priming of wood before lacquering

  • Sanding Grit 16
    Sanding Grit 16"

  • Lacquer Roller Waterbased
    Lacquer Roller Waterbased

    For waterbased products

Related products

View in same category
+2

Master TS-2K Line Marking

Line Marking for sporthalls and gyms