Maintenance Gel

Item number:

Revitalises oil-treated wood

  • Suitable for all types of oiled surfaces
  • Safe for Food Contact*
  • Makes surfaces even more durable
  • Simple application both manually and by machine 
  • Excellent results on factory-oiled/hardwax oil surfaces

*The wood sample is shown on oak

200 ML

Product details

  • Description
  • Specifications
  • Technical data sheet
  • Safety data sheet

Declaration:

Less than 5%: colouring agents.

VOC:

125 g/l, maximum VOC content (A/i (SB)): 500 g/l.

Density:

0.90-0.95 g/ml.

Shelf life:

3 years

Application Temperature:

+15-25°C and approx. 50% air humidity.

Coverage:

Regular maintenance: 20-30 m²/200 ml. Newly-sanded/non-maintained wood: 4-6 m²/200 ml.

Colours:

Natural

Cleaning of tools:

Use WOCA Solvent or turpentine

Storage:

+10-25°C. Keep out of reach of children. Do not expose to heat (e.g. sunlight). Store frost-free during winter and cool during summer.

Packaging:

200 ML

Viscosity:

20-25 Sec. DIN Cup 4

Dilution:

Undiluted

Odour:

Faint

Solid content:

85-90%

Mixing ratio:

Ready to use. Do not dilute.

Between coats:

4-6 hours at 20°C

Light use:

4-6 hours at 20°C

Recommendation:

The oiled surface should not be exposed to water for the first 2-3 days, as this can cause stains and discoloration. Wood humidity must not exceed 18%. High temperature and low air humidity will shorten drying times. Low temperature and high air humidity will extend drying times.

Fully hard:

3 days at 20°C

Re-treatment:

Repeat the oil treatment when required.

Maintenance Gel is for the care and maintenance of oiled indoor wooden surfaces and floors. The oil is quick-drying and leaves an attractive, water and dirt-repellent surface. Maintenance Gel is suitable for furniture, kitchen work surfaces, floors and other indoor wooden surfaces. It can also be used for improved results on factory-oiled/UV-oiled surfaces.

Worksteps

Instructions
Products in use
It is important that both wood and oil are at a temperature of at least 15°C, and ideally about 20°C, and that air humidity is approx. 50 %. Make sure that the room is well-ventilated, for optimal evaporation and drying time.

Always remember to test on a less visible spot to check the compatibility of the surface with the product.

  1. Thoroughly clean the surface with Intensive Wood Cleaner, mixed 1:20. Then wash with clean water. After cleaning, leave the surface to dry for at least 8-9 hours
  2. Sand the surface with 180 and vacuum clean the surface thoroughly.
  3. Apply an appropriate amount of gel to a Hand Scrubber Flex Kit White and distribute over the surface in a thin, even coat. Continue polishing until the wood seems saturated and the surface has a uniform appearance. It is recommended to work on small areas at a time, as the gel is quick-drying. For larger areas (floors larger than 4 m²) it would be advantageous to use a polishing machine.
  4. Immediately wipe down the polished surface with a clean, dry lint-free cotton cloth. When prepping with a machine, the final polishing should be done with a cotton cloth beneath the buffer. The surface should not appear wet and no excess gel should remain on the surface.
  5. If the wood does not seem fully saturated after 4-6 hours, repolish with less gel than the first treatment, but follow the same procedure.
  6. Wait 4-6 hours before using the surface. Avoid getting water or dirt on the wooden surface for the next 3 days .
When used on UV-oiled surfaces, make sure to do a more thorough final polishing to remove all excess gel.