Diamond Oil Active

Varenummer:

Oiling of wooden surfaces

  • 1-component oil with the performance of a 2-component oil
  • VOC-Free
  • Extreme durability and resistance to scratches and marks
  • High resistance to liquids such as water, coffee, tea, and red wine.

*The wood sample is shown on oak

1 L
100 ML
2.5 L
25 ML
250 ML
5 L
750 ML

Product details

  • Description
  • Specifications
  • Technical data sheet
  • Safety data sheet

VOC:

10 g/l, maximum VOC content (A/i (SB)): 500 g/l.

Density:

0.95-1.00 g/ml.

Shelf life:

3 years

Application Temperature:

+15-30°C and approx. 50% air humidity.

Coverage:

20-25 m²/L

Colours:

Smoke Brown, Natural, Extra White, White, Concrete Grey, Sand Grey, Carbon Black, Chocolate Brown, Caramel Brown

Cleaning of tools:

Use WOCA Solvent or turpentine

Storage:

+10-25°C. Keep out of reach of children. Do not expose to heat (e.g. sunlight). Store frost-free during winter and cool during summer.

Packaging:

250 ML, 750 ML, 1 L, 2.5 L

Non-slip (DIN 51130):

R10

Viscosity:

40-45 Sec. DIN Cup 4

Dilution:

WOCA Solvent (does not normally need to be diluted).

Odour:

Faint

Solid content:

95-100%

Drying time:

24 hours at 20°C

Between coats:

8-10 hours at 20°C

Light use:

24 hours at 20°C

Recommendation:

Avoid exposing the floor to water or cleaning it during the first 7 days while the oil cures. After this period, clean the floor with WOCA Natural Soap to provide additional surface protection.

Fully hard:

5 days at 20°C

Diamond Oil Active is a sustainable, VOC-free oil for wooden floors, tabletops, and furniture. This premium, single-component, low-odor oil is durable, easy to apply, and minimizes waste. Its hyper cross-linking technology creates a water-repellent, non-slip surface that’s easy to clean and maintain. With a dry matter content of approx. 99%, it’s ideal for machine application on untreated or sanded wood of any type.

Worksteps

Instructions
Products in use
Ensure that the product, room, and floor are at a temperature of 15°C to 30°C, with air humidity around 50%. The wood's moisture content must not exceed 12%. Maintain good ventilation in the room for optimal evaporation and drying. The wood surface must be clean, free from dirt, grease, wax, and sanding residue. Previously treated surfaces should be sanded down to bare wood using grit 100-120 and vacuumed thoroughly. Clean the surface with WOCA Intensive Wood Cleaner and allow it to dry for at least 8 hours before applying the oil.

Always remember to test on a less visible spot to check the compatibility of the surface with the product.

  1. Wash the floor with Intensive Wood Cleaner. Leave the floor to dry for at least 24 hours at 20°C before applying the oil.
  2. Thoroughly shake the container of Diamond Oil Active , both before and during use. Containers with different batch numbers should be mixed to avoid colour mismatch. Apply the oil using a short-bristled paint roller in an even coat.
  3. Leave the oil to be absorbed for 10-15 minutes. If the oil soaks quickly into the wood, apply more oil.
  4. Polish the oil into the wood until the surface appears saturated. Use a buffing machine with a buffing machine for large areas and a polishing cloth/pad manually for small areas.
  5. Remove excess oil with dry, lint-free cotton cloths or pads until the surface no longer appears wet.
  6. If an extra-attractive finish and resistance is desired, the floor can be repolished with 1 dl Diamond Oil Active per 10 m² within 8-10 hours hours of the first application. The oil should be polished thoroughly, as described in 4+5.
  7. The floor can be used with caution after 24 hours.
  8. Clean tools with WOCA Solvent or Turpentine.
For an enhanced finish and increased durability, the floor can be repolished with 1 dl of Diamond Oil Active per 10 m² within 8-10 hours of the initial application. Ensure the oil is thoroughly polished following the same procedure as before.